Menu
  • Home
  • Topic
  • 95 chevy s10 blazer gage cluster not working after I replace

95 chevy s10 blazer gage cluster not working after I replace

Home › Forums › Stay Dirty Lounge › Service and Repair Questions Answered Here › 95 chevy s10 blazer gage cluster not working after I replace

  • Creator
    Topic
  • November 13, 2011 at 11:00 am #441162
    ksigetteksigette
    Participant

      replace the heater core put the dash back together everything works but the rpm the mph volt temp gas so all of them

    • Creator
      Topic
    Viewing 12 replies - 1 through 12 (of 12 total)
    • Author
      Replies
    • November 13, 2011 at 11:00 am #441164
      dreamer2355dreamer2355
      Participant

        Quoted From BigC:

        Hi ksigette,

        Check the fuse for the instrument cluster panel. Was the battery disconnected during the heater-core replacement? Keep us posted.

        +1. I would also again double check your work to make sure no wiring was damage during the re installation but start with the basics first with checking the fuse.

        November 13, 2011 at 11:00 am #441165
        ksigetteksigette
        Participant

          all fuses are good the batterey was not disconneted

          November 13, 2011 at 11:00 am #441166
          EricTheCarGuy 1EricTheCarGuy
          Keymaster

            It could be that the cluster has failed or that there is a bad connection at the back of the cluster itself. Try ‘wiggeling’ the connectors at the back of the cluster, if it starts to work it’s likely a connection issue, if not the problem could be in the cluster itself.

            November 13, 2011 at 11:00 am #441167
            LudstoysLudstoys
            Participant

              Was wondering if u hooke the ground wires back of the dash. Nother thing to c with a wold meter if there is power in the plug for the cluster.

              November 13, 2011 at 11:00 am #441168
              ksigetteksigette
              Participant

                on the cluster plug i found a bent pin so ill keep u all posted

                November 13, 2011 at 11:00 am #441169
                jacobnbr1jacobnbr1
                Participant

                  Hook a good scan tool to it and ping the IPC module and see if it is on line or not. If it is off line then either it is missing a power source, ground or communications.

                  If it is on line then do a sweep test and see if all the needles move etc…

                  November 13, 2011 at 11:00 am #441170
                  ksigetteksigette
                  Participant

                    there was a pin bent on the cluster

                    November 13, 2011 at 11:00 am #441171
                    dreamer2355dreamer2355
                    Participant

                      Thanks for the update!

                      November 13, 2011 at 11:00 am #441172
                      Trcustoms719Trcustoms719
                      Participant

                        Indeed, thanks for the update!

                        November 13, 2011 at 11:00 am #441163
                        BigCBigC
                        Participant

                          Hi ksigette,

                          Check the fuse for the instrument cluster panel. Was the battery disconnected during the heater-core replacement? Keep us posted.

                          October 31, 2018 at 3:03 am #891256
                          JamesJames
                          Participant

                            DID U FIGURE OUT WHAT IT WAS??? I HAVE SAME PROBLEM
                            GAUGES DON’T WORK AND TEMPERATURE GAUGE GOES ALL THE WAY UP TO HOT

                            February 7, 2019 at 12:42 am #892466
                            BillBill
                            Participant

                              What did you find with the cluster? Same issue. Cluster was tested and is good.

                            • Author
                              Replies
                            Viewing 12 replies - 1 through 12 (of 12 total)
                            • You must be logged in to reply to this topic.
                            Loading…