Forum Replies Created
-
Replies
-
New Rubicon front trackbar installed, used Nord-Lock washers to secure the bracket.
[url=https://www.upload.ee/image/8469851/20180522_191958.jpg]
Both pinion seals where leaking, now ones are in – I hope it lasts.
[url=https://www.upload.ee/image/8460994/20180519_114454.jpg]
[url=https://www.upload.ee/image/8460996/20180519_115659.jpg]
[url=https://www.upload.ee/image/8460997/20180519_115739.jpg]
Hello
So I replaced my insturment cluster bulbs. (removed the ABS bulb)
Some pictures, maybe it will help someone – really easy on the 93-95.
[url=https://www.upload.ee/image/8390152/95JZ_dash_remove.jpg]
[url=https://www.upload.ee/image/8390154/20180501_115528.jpg]
[url=https://www.upload.ee/image/8365410/20180420_183538.jpg]
[url=https://www.upload.ee/image/8365412/20180424_200806.jpg]
Double cardan rebuild:
[url=https://www.upload.ee/image/8365434/20180416_172043.jpg]
[url=https://www.upload.ee/image/8365436/20180416_205719.jpg]
[url=https://www.upload.ee/image/8365404/20180420_175314.jpg]
[url=https://www.upload.ee/image/8365406/20180420_175911.jpg]
[url=https://www.upload.ee/image/8365403/20180420_183438.jpg]
More work done:
* New bump stops in the rear
[url=https://www.upload.ee/image/8326597/20180409_172237.jpg]
* New wires etc
[url=https://www.upload.ee/image/8326602/20180408_160215.jpg]
* New hoses to the tranny cooler
[url=https://www.upload.ee/image/8326610/20180413_182147.jpg]
* One more cooler in the front for the power steering fluid
[url=https://www.upload.ee/image/8326614/20180409_210132.jpg]
[url=https://www.upload.ee/image/8326615/20180413_191435.jpg]
Had a coolant leak this morning:|
Yes- it was this stupid little hose between the block and the pump. I did not replaced it when I did the water pump 2.5 years ago. Now I know better.
Old vs new:
[url=https://www.upload.ee/image/8146337/20180307_172523.jpg]
[url=https://www.upload.ee/image/8146336/20180307_173024.jpg]
[url=https://www.upload.ee/image/8146338/20180307_174740.jpg]
After the lift, the rear axel was still too close to the body, so I put a set of JK rear upper CA on, to get the axel more center,
[url=https://www.upload.ee/image/8137542/20180219_135801.jpg]
[url=https://www.upload.ee/image/8137537/20180305_180452.jpg]
[url=https://www.upload.ee/image/8137539/20180305_190032.jpg]
Also waiting the trackbar brackets to center the axels.
[url=https://www.upload.ee/image/8137554/20180228_120223.jpg]
Also new trunk “bushings”:
[url=https://www.upload.ee/image/8137555/20180228_135427.jpg]
Engine mounts where shot.
Right side:
[url=https://www.upload.ee/image/7889963/20180114_135726.jpg]
Left side:
[url=https://www.upload.ee/image/7889959/20180114_125254.jpg]
[url=https://www.upload.ee/image/7889958/20180114_125240.jpg]
Left side bracket is wrong size – too wide to fit the engine block, so I pressed the bushing out from the new and replaced it with the old.
[url=https://www.upload.ee/image/7889961/20180114_132608.jpg]
[url=https://www.upload.ee/image/7889962/20180114_132618.jpg]
New rear main seal was installed, with new pan seal etc.
[url=https://www.upload.ee/image/7803481/20171221_182420.jpg]
The real main seal was not offset in the bearing cap, and the oil pan seal was heavy with RTV, so thats why it leaked.
I hope I did some better job.
Rear bumper waits for install:
[url=https://www.upload.ee/image/7655182/20171111_151736.jpg]
[url=https://www.upload.ee/image/7655183/20171111_151756.jpg]
[url=https://www.upload.ee/image/7655184/20171111_151746.jpg]
So I had some exhaust smell in, when driving with an open window. The solution was to install manifold gaskets that factory idiots never did.
I also had some painted manifolds on my spare engine, so they where changed.
[url=https://www.upload.ee/image/7535150/20171006_174151.jpg]
[url=https://www.upload.ee/image/7535149/20171006_174137.jpg]
[url=https://www.upload.ee/image/7535151/20171007_145038.jpg]
Number 3,5 and 8 where leaking.
[url=https://www.upload.ee/image/7535153/20171007_145831.jpg]
[url=https://www.upload.ee/image/7535154/20171007_145902.jpg]
