Honda Rear jacking point

[skim3544]

Where is the good location for rear jacking point for Hondas for floor jacks?

Topic

[DA9 Integra]

hes tried that, but if the jack is n the pinch welds, his question is where would he put the jack stands, he cant just pull out the jack fast and put the jack stands lol

[twiggy]

I had a jack that I couldn’t get things quite high enough, then I found that my jack was low in hydraulic oil due to my storing it in its’ carry case sideways with the release open. When I topped that oil off, I suddenly was able to jack things high enough to put stands where I need.

Just wanted to throw that out as something to check.

[hondaslave1342]

i have a 2001 accord and when i jack up the rear i put the jack on the very end of the pinch weld,,,it leave’s enough room to put the jack stand…

[Matt]

You could always do one side at a time using the pinch welds. These are the downward facing seams along/under the rocker panels. You don’t have to do both sides at the same time if your jack doesn’t go high enough. Make sure you chock the opposite wheels. For instance, if you are raising the rear end, put something in front of the front tires, and vice versa. Use the trans or the parking brake to assist you in either case.

[losercomet]

Have you tried the pinch welds at the rear of the car in front of the rear tires and lifting one side adding a jack stand then doing the other side?

[skim3544]

Quoted From losercomet:

Have you tried the pinch welds at the rear of the car in front of the rear tires and lifting one side adding a jack stand then doing the other side?

I am confused – If I lift using the rear pinch welds, where can I put the jack stands?

[DA9 Integra]

wat u can do is try to jack up the car from the rear tow hook or around those areas, just be careful its secure and wont damage the car and than u can put the jack stands on the pinch welds (thats how ive done it especially since its easier for me since my car is slammed ^^)

[skim3544]

Quoted From DA9 Integra:

wat u can do is try to jack up the car from the rear tow hook or around those areas, just be careful its secure and wont damage the car and than u can put the jack stands on the pinch welds (thats how ive done it especially since its easier for me since my car is slammed ^^)

Yes, that is what I have been trying – but every time I do that I end up jacking as high as my 3 ton Sears jack can go, but still not high enough for my 3 ton jack stands to slide under. I was able to do this once by adding a block of 2×4 on top of the jack but I feel unsafe doing this because the hook isn’t flat and adding a flat piece of wood does not look right.

[DA9 Integra]

is your car stock height? (asking cuz my car is lowered and can not even fit a small jack under it) wat u can also try is lifting it from under the control arms, where the control arms connect to the body, under where the bushing is, im not sure if it will work, i would go check lifting points on my integra but its pouring outside so i cant check rite now, try to see if u can do that if u cant ill go check

[DA9 Integra]

here is a link of a photo i found, i dont know if there r parts of the body that u can use as lift points but heres a pic of wat it might look like

http://www.littlemini.us/technical/exhaust/DSCN3767.jpg

[college man]

how about in front of the rear wheels on the frameC8-)

[EricTheCarGuy]

In that situation I normally go for where the rear control arm attaches to the body in the inside mount, you’ll need to do one side at a time but it does work.

[cb7ftw]

I just use a short 4×4. Also, if the jack stand is just a little to tall, you can often slide it in from the back, to the front of the body pinch welds. Getting closer to making a video on how to jack up Civics.

[Author]

Replies